God Hand PN-120 single-edged nippers

Product Information

This cookie, set by YouTube, registers a unique ID to store data on what videos from YouTube the user has seen. The wide cutting board edge supports an object firmly leading to minimum deformaties due to cutting. The sharpness of the cutting edge achieves a smooth cut surface as if sharpened with a design knife and minimizes plastic whitening (a phenomenon in which the cut section turns white).

DSPIAE have now released the 3.0 version of these, but I have seen little difference between them and the 2.0, so if you can get the 2.0 still, grab them. they are just as good. These, like the Godhand, are however more fragile than any of the other cutters on this list. they’re a different beast. I’ve broken my first pair of Godhand because I did not heed the warnings. But now I know, it won’t happen again. It’s simple really. As you are cutting the plastic, don’t bend and flex them, the sharp blade is so fine (that’s what makes them cust so cleanly) is thin and it can snap if flexed. don’t flex it. We're not just making that up - Pete, James and Foxx have sworn by them for years and we are ridiculously excited to be able to bring them to you now. They truly are tools that are at home whether they are in the hands of a beginner or a professional. These are not mass-produced throwaway tools; they are tools designed by and for master craftsmen that will enable you to create incredible art.Ultimate Ultra-Thin Single-Edge! Ultimate Sharpness! When cutting small parts, it will not fly away. It will decrease the amount of time spent searching for the fly away parts. You can see the similarities between this and the Godhand, in fact, even on close inspection, other than one being red and the other being blue, there is very little difference. Even the curves in the metal are pretty much identical with only some minor flourishes like the retaining screw and spring extension protector being in a slightly different place.Do not twist the blade during cutting or when removing the blade from the runner after cutting. Doing so causes a rotating force to apply to the blade and can cause it to break For people who paint plastic models, this is the best nipper to use because when they cut along the edge, it leaves no remains of the gate. It leaves with a clean cut section. This shortens the time spent on filing the gate. They make a good cut and are nice and sharp. Another set which has one flat edge and one cutting edge. However had issues with them, the flat edge was offset meaning my cutting edge was never able to cut flush. This is only useful when the connection to a sprue is against a flat edge of a model component, but most of my models have this connection on a rounded edge. whilst the cut itself was smooth it often left a nub of sprue on the model surface which I needed to clean off with a hobby knife. These are cheaper, yet very nice side nippers. GSI Creos are a solid brand from Japan, arguably second only to Tamiya. In my opinion they are pretty competitive. The price of those is right, they are comfy and can last you long. There are other, not-so-precise options from the same brand, but the set here is the one that I would recommend if you are serious about your hobby. Number 2: A good nipper will be your dependable ally in even the roughest of builds and cuts. The best way to protect it and make it last is with proper maintenance and usage. In this blog, we’ll be talking about the basics of how to use and care for your GODHAND Nippers to ensure that the time you spend with them is long and worthwhile. Summary

From the second I got my hands on these I actually (for the first time ever) enjoyed cutting models from the sprue. They reduce (not remove) the amount of post clean up you need to do before painting. 1. DSPIAE ST-A Single Blade Nipper Hold it up to the light and gradually tighten the grub screw until no more light is visible between the nipper's jaws. If necessary, loosen and tighten it until it looks just right. There are two main types of cutter on this list Flat Edge and Dual Cut. On flat-edge cutters, one side of the cutters is flat. instead of cutting the plastic this edge acts as a stop allowing the other side to cut from only 1 direction. dia-cut is where both sides have a cutting edge and cut the plastic to meet in the middle. In my experience, wither of these really offer a better cut as both leave a bit of residue on the model. However, the flat-edge cutters do seem to last longer as you aren’t having 2 blades cut into each other. Records the default button state of the corresponding category & the status of CCPA. It works only in coordination with the primary cookie.There is a saying that the craftsman is only as good as his tools. That is 100% true for scale modeling too. Especially when it comes down to nippers. They can be a destroyer of dreams, especially when the curvy plastic is soft and attached to the sprues just where it shouldn’t be. Nippers can be of a lot of help, as well as cause a lot of trouble. They can be a deal breaker /and especially/ with delicate parts or round elements. Imagine Please do not twist the blade during cutting or releasing from the runner. Twisting may cause it to break under load. these are not just nippers. Tools mentioned above are not only one of the best available, but they are also a way to keep the plastic of the parts you cut intact. They are the way to a better and easier modeling. They are also reliable products and well worth the money. Either one of those won’t hurt a modeler’s budget, especially with recent kit’s prices. But at some point the investment will return. Sometimes, just one little defect can ruin the whole model. And all the modeling starts with cutting the plastic from the sprue. Please do not cut plastics that are too long for the blade. The load will be applied to one point, causing it to break or bend.

A cookie set by YouTube to measure bandwidth that determines whether the user gets the new or old player interface. Ultra-thin “cutting edge” is created one by one by a well experienced craftsmanship in Tsubame-Sanjo, Niigata prefecture, Japan. If I make sure I’m holding the nippers exactly parallel with the part, I don’t leave an indent or raised angle. If I do it right, I can skip right to filing or sanding. The blade gets thinner and more delicate towards the tip, so cut as close to the centre of the blade as possible Hands down, God Hand Ultimate Nippers /SPN-120 5.0/ is the best set of nippers available. Expensive, but perfect. They are more precise than any of the sets mentioned above, thus the price. Made in Japan, they are very popular with modelers that are interested in various subjects. From Gundam to small 48th and 72nd armor. And those nippers deliver best performance that you can ever get. If you are not sure what to get, but you have the money, this is the set for you. Preferably combined with one of the not-so-precise options available.

Account & Support

Shave & Cut” structure allows a smooth cut surface as if it is cut off by a design knife and it minimizes plastic whitening. A Step by Step Guide on How to Use and Maintain GODHAND PN120 Nipper A Step by Step Guide on How to Use and Maintain GODHAND PN120 Nipper